FPM (FKM) is manufactured by Viton Du Pont. Semi-finished stitched ...
Since the beginning of 2017, the payers in the FSS will be able to compensate for the cost of buying specials, workwear and other personal protective equipment (PPE) at the expense of injury contributions.
Moreover, the reimbursement is subject to only the cost of overalls produced in Russia and from Russian materials.
Legislative acts
Order of the Ministry of Labor of the Russian Federation №201N dated 04.29.2016
The order makes changes to another order, No. 580H dated 10.12.2012, on financial security measures to reduce injuries and tradeboles. Data data, in addition to PPE, regulated the procedure for addressing the allocation of funds to other similar objectives:
- providing employed medical and prophylactic nutrition (milk);
- providing advantages to sanatorium-resort treatment for such employees;
- carrying out;
- purchase of aidhechki, and for transport enterprises - tachographs and alkotesters;
- training and retraining of specialists of software;
- assessment of working conditions and;
- other similar events.
The insured will need to prove:
- compliance of certified jobs working places and professions for which the provision of PPEs is laid;
- compliance with the technical model of the Customs Union "On Security SIZ" No. 878 of 09.12.2011;
- compliance with all SIZ issuing standards.
Order of the Ministry of Health and Social Development №290n of 01.06.2009
The order contains general inter-sectoral rules that apply to all employers, as well as the definition of PPMs - strictly individual means of protection that are intended:
- to protect against contamination or temperature conditions;
- to reduce the degree of impact on working harmful factors.
Permissible registration of the lease agreement and temporary use. Products must be certified. The employee must be notified of the norm applied to his position.
Priority in the provision, according to the order, belongs to the industry standards according to the type of activity of the enterprise, and for workers through professions that exist on a variety of enterprises - on the norms of work.
Cell-to-end professions and general issuing criteria
Order of the Ministry of Labor of the Russian Federation No. 997n dated 09.12.2014, the norms of extradition for the year for a list of 195 through occupations were established.
Drivers of trucks, tractors and autocrantes are laid:
- one suit;
- 6 pairs of gloves with polymer coating.
Gas welder, electric gas welder, electric welder, welder of reinforcement, plastics: 
- suit protecting against splashing molten metal;
- two pairs of leather boots protecting against sparks and elevated temperatures;
- two pairs of leather boots protecting against sparks and elevated temperatures;
- dielectric Gloves, bots, rugs;
- 6 pairs of polymer coating gloves, 12 gloves with protection against splashing molten, gloves with point spraying as wear;
- protective heat-resistant shield (welder mask) with a light filter or glasses with similar characteristics;
- protective glasses, respirator - before wear.
Storers and sellers of non-food products are issued under normal conditions, without the impact of hazardous substances:
- two apron with a bib;
- monthly - gloves.
Veterinary doctor, animal breeder, grains are provided:
- suit or bathrobe with trousers to protect against contamination;
- apron with a bib;
- pair of rubber boots;
- once a quarter - gloves.
Janitor or territory cleaners get: 
- suit for protection against pollution;
- two apron with a bib;
- rubber boots;
- once every two months - gloves.
In addition to through occupations, typical norms provide for the provision of employees of all industries:
- climate adapted workwear and shoes (Resolution of Mintrud No. 70 dated December 31, 1997);
- special reflective and signaling clothes (order of the Ministry of Summer №297 dated 20.04.2006).
So, the clothing is designed for comfortable on the outside of the premises during the winter months within two hours at medium negative temperatures and the average wind speed:
- 4 Class of protection operates for the districts of the North and Polar region (special belt), with a winter temperature -25 ° C and a wind of 6.8 m / s;
- Grade 3 (Central Siberia, North of the European part of the country, Kamchatka, Sakhalin, Kuril Islands) with temperatures from -41 ° C;
- Grade 2 (south of the Far East, Middle and South Urals, South Siberia, Udmurtia, Tatarstan, Karelia, Kirov region) Temperature from -18 ° C, Wind 3.6 m / s;
- Grade 1 (southern and middle European part of the Russian Federation) Temperature from -9,7 ° C, wind 5.6 m / s.
For a special climatic belt, for example, issuance is provided: 
- the costume protective on the insulation lining (similarly - protective suits from
- acids, fire, sparks) - for a year and a half;
- the jacket is protective on the insulation lining, insulated pants - for a year and a half;
- handwood and hat-Ushanka - for three years;
- moisture-resistant boots and fur mittens - for two years;
- boots and boots - for a year.
When dismissing employees, the employer must publish an order. The form on which it is filled, you will find.
Industry standards and rules
Specialists in labor protection, which know the specifics of production in each industry, developed a whole list of standards for the provision of individual activities and even Holding (Gazprom, Surgutneftegaz). All the rules are approved by the orders and regulations of the Ministry of Labor and the Ministry of Health and Social Development of the Russian Federation. In total, such documents are approved to date about 70: 
- №416n dated August 12, 2008 - Agriculture, water management;
- №68 dated December 29, 1997 - Fish and forestry, pulp and paper production, microbiology, pharmaceuticals;
- №341n of 02.08.2013 - coal mines;
- №61 dated 08.12.1997 - peat harvesting, woodworking;
- №906n dated 11.08.2011 - Himprom;
- №652N of 01.11.2013 - Metallurgy;
- №1104N dated December 14, 2010 - Mechanical Engineering
- №357N dated 06.22.2009 - Motor transport and road device.
- According to order No. 1104 of 14.12.2010, the regulations of the PPE for machine tools were determined.
Tokar, Pour, Grinding, Milling:
- suit for protection against pollution;
- leather shoes with protective feet;
- mittens or gloves (for working with crane-beam);
- anti-aerosol respirator (when processing cast iron).
Order No. 357N dated 06.22.2009 The regulations of the SIZ for road workers were identified:
Asphalt concrete room (except for the winter season):
- suit or jumpsuit signal;
- leather boots or shoes with a protective feet;
- protective glasses and helmet with a credit card;
- tarpaulin mittens or knitted gloves;
- knee pads;
- headphones or earplugs;
- respirator.
In winter, additionally:
- costume on the insulation lining signal;
- waterproof signaling raincoat;
- heated leather boots or felt boots.
For road works:
- signal vest.
SIZ, issued to each particular employee, must correspond to its floor, growth, size.
The worker is obliged to apply the PPC correctly. In case the employee refuses to use overalls and protective equipment Employer has the right to remove a person from work and impose 
In addition to clothing, shoes and protection items, regulations set the provision of disinfecting and fluttering liquids (soap), protective creams for hands. The issuance of all PPEs is fixed in the employee's card, the card in electronic form confirm with reference to the document containing the signature of the received.
Caring for the health and security of an employee in the process of work is not right, but the duty established by the state legally. In common interest, to prevent, as far as possible, accidents and proceedings in production.
* Information is posted for informational purposes to thank us, share a link to the page with friends. You can send the material interesting to our readers. We will be happy to answer all your questions and suggestions, as well as hear criticism and wishes at [Email Protected]The work of Plumbing and the Master for Home Repair is related to the use of various manual and electrical instruments. These are grinders, perforators, even welding machines, at the same time, work is associated with moisture. Therefore, to properly pick up the clothes of the plumbing is not only for reasons of convenience, but also for safety. If plumbing works have to do intensively, it would be good to purchase several summer and winter costumes to shift. What kind of clothes need plumbing?
Work suit
Plumbing suits sew from such fabrics that pushed moisture, can protect the body from sparking. Comfortable suits with many pockets, as the plumber can put several small details and tools in them. Under the working suit, it is best to wear native clothes from natural fabrics, which is detonated. Plumbing does not always work indoors, because for the winter they pick up warmed workers suits, jackets.
Many masters of domestic repairs pick up such a type of clothing as a jumpsuit, it does not need to constantly fill the T-shirt, movements can be freer. There are winter overalls that are perfectly held inside the heat. Workwear rarely happens light shades, more often it is green, blue or black. Store overalls will offer a wide variety of products, in which not only convenient, but also safely.
Gloves
Gloves are necessary for plumbing not only in order to protect in winter hands from the cold. This is the main means of protecting hands from mechanical damage, they also simplify work. Plumbing takes a lot of building materials, conventional fabric gloves will protect from corns and rubbing. There are special gloves in which you need to work with electricity or welding. Pipes are convenient to take fabric cotton gloves to which PVC or Nitrile is applied. Also in such gloves it is easier to hold the perforator and other instrument.
Respirators
When the holes are drilled in the walls under the pipe, you need to use the respirator so that the dust does not get into the respiratory organs.
Glasses
Points can not be called clothes, but they are an important protective means of plumbing. There are special glasses for welding, it may be necessary to protect the eyes from entering mechanical objects and dust. They are made of durable glass or polycarbonate so that in the event of breaking the fragments did not paint the eyes.
Headdress
In winter, a warmed baseball cap or helmet can be used if construction is held nearby.
Working shoes
As working shoes, both ordinary shoes, on thick soles and rubber shoes, boots and galoshes from polyvinyl chloride are used. Footwear from polymer composite material (EVA) is convenient because it is light, at the same time, well protects against moisture.
Any professional uses special clothing for work. It not only protects and warms, but also increases the importance in the client's eyes.
Overalls for plumbers - an important attribute of the work of each employee, whose work is connected by sanitary engineering. Not only the quality of the work performed, but also the level of productivity and safety of the specialist depends on the quality of the form in some cases.
What are the requirements of plumbing overalls
Professional plumbing activities are often conjugate with certain difficulties. In addition, troubleshooting is not always carried out in a house or apartment - often you have to work on the street. The scope of plumbing includes a number of works: cleaning septicities in country houses, repair and cleaning of pipes, troubleshooting, etc.Such features of working activities involve the use of workwear for plumbers, as well as providing workers with reliable and high-quality shoes. For example, it can be a "euro" low shoes polyurethane, leather with a fortified feet. The presented shoes will ensure the protection of the employee under conditions of high humidity, as well as in extreme conditions (for example, when carrying out power lines).
Plumbing overalls must meet all the standards and standards of GOST, which regulate the provision for providing enterprise employees to uniform. Moreover, the form for this category of employees should be resistant to pollution, have a water-repellent coating and protect a person from the negative impact of environmental factors.
Overalls for plumbers can have different versions
Sewing forms can be carried out according to individually designed drawings. It is very convenient, especially for the staff of large companies that provide plumbing services. For example, to perform work on the street, the form can be equipped with additional elements, have a lot of pockets, as well as fasteners for fixing tools. You can also use a full-fledged Specialist Suit with a semi-overalls or to make a set, taking into account the professional features of a specialist.In winter, as well as at night, overalls for plumbers are complemented by vests with reflective stripes. If the working conditions bear the potential danger to the Contractor, it is necessary to provide appropriate means of individual protection.
Instruction number ___
Instruction
For labor protection
plumbing
1. GENERAL REQUIREMENTS OF LABOR PROTECTION
1.1. Employees are allowed to self-work as a locks-sanitary engineers:
- not under 18 years old;
- past medical examination;
- past introductory instructions;
- past primary instructions;
- past learning and internship in the workplace;
- tested knowledge of labor requirements;
- having a group of electrical safety is not lower than i and appropriate qualifications according to the tariff-qualification reference book.
1.2. The plumbing stop should take:
- re-instructing on the safety of labor in the workplace is no less often than every three months;
- internship;
- unplanned and targeted instructions: when changing the technological process or rules for labor protection, replacement or modernization of industrial equipment, devices and tools, change conditions and organization of labor, in violations of labor protection instructions, breaks in operation of more than 60 calendar days (for work to which the increased security requirements are presented - 30 calendar days);
- dispensary medical examination.
1.3. Plumber is obliged:
- perform only the work that is determined by the working instruction;
- perform the rules of the internal labor regulation;
- correctly apply the means of individual and collective protection;
- comply with the requirements of labor protection;
- immediately notify your immediate or higher leader about any situation that threatens the life and health of people, about every accident that occurred in production, or on the deterioration of their health, including the manifestation of signs of acute professional disease (poisoning);
- undergo training to safe methods and techniques for the work and first aid to be affected by work, instructions on labor protection, verification of knowledge of labor protection claims;
- undergo mandatory periodic (during work) Medical examinations (surveys), as well as undergo extraordinary medical examinations (surveys) in the direction of the employer in cases provided for by the Labor Code and other federal laws;
- to be able to provide first prefigure assistance to affected electric current and with other accidents;
- be able to apply the means of primary fire extinguishing;
- know the location of the means of rendering a prefigure aid, primary means of fire extinguishing, main and spare outlets, evacuation routes in the event of an accident or fire;
- while working to be attentive, not distracted and not distracting others, to prevent persons who are not related to work on the workplace;
- contain workplace clean and order.
1.4. The plumbing mechanic should know and follow the rules of personal hygiene. Each food, smoking, resting only in specially designated rooms and places. Drink water only from specially intended for this installations.
1.5. During work on locksmith-sanitary engineering, the following dangerous and harmful production factors can affect:
- moving machines and mechanisms;
- moving parts of manufacturing equipment;
- destructive structures falling objects;
- insufficient illumination of the working area;
- lack of natural light;
- increased dusting, air base gas zod;
- increased temperature of equipment surfaces, materials; increased or reduced air temperature of the working area;
- increased mobility, air humidity;
- increased noise level in the workplace;
- sharp edges, burrs and roughness on surfaces of blanks, tools and equipment;
- increased voltage in the electrical circuit.
1.6. The plumbing mechanic must be provided with workwear, footwear and other personal protective equipment in accordance with the "typical sectoral standards of free issuance of special clothing, special shoes and other personal protective equipment" and a collective agreement:
- tarp costume - 18 months socks time;
- rubber boots - 12 months;
- combined mittens - 2 months;
- rubber gloves - duty;
- glazing gas mask - duty.
Outdoor works in winter additionally:
- cotton jacket on insulation laying - 30 months;
- cotton trousers on the insulation laying - 30 months.
Store special clothes and shoes follows in the cabinets, and the warm clothing in the summer period is to keep storage to the warehouse. All overalls and shoes should be put in the prescribed manner and take it in washing and repair.
1.7. In cases of injury or indisposition, it is necessary to stop working, notify about this work manager and contact the medical institution.
1.8. For non-fulfillment of this instruction, the perpetrators are involved in responsibility, according to the legislation of the Russian Federation.
2. Requirements for labor protection before work
2.1. The plumbing mechanic should know that work on the repair, inspection and prevention of sewage and water wells, holes, tanks and structures are the works of increased danger, so they must be carried out by a brigade of workers of at least 3 people after receiving an instruction on labor protection and outfit Admission to work work.
2.2. Before the production of works in the wells, the locksmith should wear a good workwear and shoes, a protective hard hat, as well as get safety belts with a rope, which in length should be 2 meters to be longer than the depth of the well, along the entire length at a distance of 250-300 mm have nodes and be checked To break the load of 200 kg, get gas analyzers or gas indicators, battery lamp 12 volts, manual fan, fences, posters of the installed sample, hooks and breaks for opening covers and hatches of wells, buckets, tool. All obtained tools for work must be checked for their health.
2.3. Install from open wells, holes necessary fences, warning posters and road signs. In the dark day on the racks of signal signs, hang lanterns with red lenses.
2.4. Check in the well, the serviceability of the bracket or stairs, for 6-8 hours before the start of work, open the lids of the hatches of two adjacent and working wells for their ventilation.
2.5. Take steps to disconnect pipelines summarizing to sewer devices and post the poster with the inscription: "Do not include - people work!".
2.6. With the help of a gas analyzer or gas indicator, check and make sure that there are no gases at the bottom of the well (methane, carbon dioxide, sulfur, etc.).
2.7. Prepare a tool, as well as billets of pipes, Signs, couplings necessary for work.
2.8. Check the tool and fixtures you need and make sure of their health.
2.9. Handles of the hand tool must be smooth and have an oval shape, files, rashpille, etc. With a pointed work end, it must be fixed in a flat, smoothly strung handle, pulled from both ends with metal bandage rings, chisels, critsens should not be damaged on the working Parts in the form of sharp edges in the seizure of hand, cracks and burrs in the occipital part, used wrench keys must correspond to the sizes of bolts and nuts. It is not allowed to lengthen the wrenches by nozzle of gas pipes or the second key extensions, the verses must be with strictly parallel sponges and are equipped with soft metal strips (copper, brass, etc.).
3. Requirements for labor protection during work
3.1. The plumbing mechanic is required to contain workplace clean and order, do not clutter it with materials, blanks, details and outsiders, timely remove metal waste in the place allotted for them.
3.2. Do not lift and not tolerate gravity over the established norm (50 kg for men).
3.3. In order to avoid electric shock, do not touch the open current-generating parts of the electrical equipment, do not open the doors of electrical distribution cabinets, do not remove the housings of the starting devices and so on.
3.4. The workplace tool is located so that it is eliminated with the possibility of rolling or falling. It is not allowed to lay a tool on the railing of fences or a non-fired edge of the forest site, lumps.
3.5. When working a shock action tool, use protective glasses to prevent solid particles from entering the eyes.
3.6. Screwdriver choose the width of the working part (blades) depending on the size of the slot in the screw of the screw or screw. When unscrewing the screws or screws, especially the pruring, firmly fix the part in the vice, do not keep it in hand.
3.7. The size of the oz (capture) of wrench keys should not exceed the sizes of the bolts (faces of nuts) by more than 0.3 mm. The use of lining in the gap between the planes of the keys and heads of the bolts or nuts is permissible forbidden.
3.8. When unscrewing nuts and bolts, it is not allowed to lengthen the wrenches with additional levers, second keys or pipes, except the "asterisk" type keys. If necessary, apply keys with long handles.
3.9. With manual cutting of metals with knife needed:
- firmly fix the processed detail or workpiece in the vice;
- properly adjust the tension of the hacksaw blade, since with a weak or excessive tension, the canvas can burst;
- at the end of the cutting, weaken the pressure on the hacksaw and hold the cut part to the hand, so that when it is not injured, it is not injured.
3.10. When cutting the sheet metal with hand scissors, it is prohibited to use auxiliary levers to lengthen the handles or cutting with blows on blades or handles.
3.11. When cutting, the editing of the sheet metal to wear mittens to protect hands from injury by sharp edges of metal sheets.
3.12. Removed when repairing equipment components and parts stable, if necessary, fasten them.
3.13. When disassembling press compounds, use special puller (screw, hydraulic, etc.).
3.14. Wash the kerosene parts in a special container in the place allotted for these purposes. Contaminated kerosene residues to drain into the designed container with a tightly closing lid.
3.15. When assembling nodes and mechanisms, the coincidence of the holes in the parts connected to the parts using special mounting mandrels, in order to avoid injury not to check the coincidence of the fingers.
3.16. When operating the power tools in order to avoid injury or electric shock, it is prohibited:
- stretching, twisting and engaging the cable, put the cargo on it, as well as allow it to cross it with cables, cables and gas welding sleeves;
- disassemble and independently repair the power tools, cable, plug connections and other parts;
- work with power tools from the substained stairs;
- remove chips or sawdust with your hands while the tool is operating (chips should be deleted after a complete power to the power tool with special hooks or brushes);
- concerned by the hands of a rotating cutting tool;
- processing the power tools iced and wet details;
- operate the power tools in the effects of droplets and splashes, as well as on open areas during snowfall or rain;
- leave without supervision the power tools attached to the network, as well as transfer it to those who do not have the right to work with it;
- working the power tools that has expired periodic checking.
3.17. The power tool cable must be protected from accidental damage and contact with hot, raw and oil surfaces.
3.18. Installing the operating part of the power tool into the cartridge and remove it from the cartridge, and also adjust the tool only after turning off it from the network plug and at a complete stop.
3.19. When working at an altitude (more than 1.3 m from the surface of the soil, overlap, flooring, floor), comply with the requirements of the instructions for labor protection when performing work at height.
3.20. If you need to perform work on a sharpening or drilling machine, comply with the requirements of labor protection instructions when working on these machines.
3.21. All repair work on active pipelines, in addition to pulling up the flange compound bolts, the seals, produce only after turning off the water supply to the repaired area.
3.22. When the pipeline is turned off (or its site) to repair the closed valve or the valve, squeeze a sign with an inscription that prohibits the water supply to the repaired area, the valve flywheel (valve) lock on the lock, between the flanges put the stubs with shanks between the flanges.
3.23. Disassembly of pipeline connections to produce gradually, water or condensate residues from the pipeline into a predetermined container.
3.24. In the absence of devices that allow you to pre-release from the water, the disconnected area of \u200b\u200bthe pipeline or any equipment, their emptying to weaken the part of the flange bolt from the side opposite to the place of its location.
3.25. When servicing the cast-iron fittings, pulling up the flange compound bolts at the temperature of the coolant is not higher than 90 degrees. C. If necessary, this can be done at a higher temperature, but the pressure in the pipeline does not exceed 0.3 MPa (3 atm.). Tightening the seals is allowed at a pressure not higher than 1.2 MPa (12 atm.).
3.26. In order to avoid injury, pulling up coupling fittings and nuts of instrumentation (to eliminate leaks through threads) to produce proper sizes. Do not apply gas keys for these purposes, as well as extension levers.
3.27. Filling the pipelines included in the current network, to produce through the reverse line. In order to avoid the density of flange compounds and damage to the welded joints, the temperature in the thermal network is gradually and evenly, at a speed of not more than 30 degrees. C per hour. Do not fill the heat network with water with a temperature above 70 degrees. C.
3.28. The inclusion of heat supply installations after the completion of the repair work is made only with the permission of the work manager.
3.29. When performing work at a height, do not leave the details of the repaired pipelines, even with a short-term break in operation.
3.30. With a technical (deep) inspection and performance of work related to descent to the well, comply with the following security requirements:
- work in the well to produce a brigade consisting of at least three employees, one of which works in a well, the second - on the surface, the third specially observes the work and, if necessary, assists working in a well. It is forbidden to distract observing on other work as long as working in the well does not rise to the surface. From the team of the brigade, the person responsible for carrying out works;
- the well cover is discovered using a special hook and scrap, it is forbidden to open the cover with your hands. At the open well, establish a fence and warning sign;
- before starting work in the well, make sure that there is no zagaznost in it, for which the gas analyzer is for
- when a gas acquisition is detected, the well should be ventilated by natural ventilation or forced ventilation;
- before descending into the well, make sure the strength of the bracket (stairs) with the help of a pole, put on a helmet and safety belt (with shoe belts) with a safety rope, firmly fixed outside. The length of the safety rope must be at least 2 m more than the depth of the well. It is not allowed to work in a well without safety belt and helmets;
- if the gas from the well is not completely removed, it is possible to descend into the well only in a gas mask of the PSH-1 brand or PSh-2 with a hose overlooking the surface at least 2 m. In this case, the brigadier or the head of work should be observed in the well. Working in a federation in a gas mask with a discharge hose is allowed without a break for no more than 10 minutes;
- to illuminate the workplace in the well, apply a battery lamp with a voltage not higher than 12 V;
- with a sharp deterioration of well-being, immediately serve the signal to observe, stop working and enter the surface.
3.31. When performing the maintenance or repair of thermal items to comply with the following security measures:
- all shutdowns, switching and inclusion of local systems produced in the starting, stop or normal operation process, performing alternately valves on the feed and return lines of the heat pipe, while ensuring that the pressure in the system does not rise above the permissible;
- disabling the system to produce alternately closing valves, starting with the feed line, and the inclusion of the system on the contrary - from opening the valve on the reverse line;
- tightening flange connections bolts and pulling up the fittings of the fittings evenly, along the contour in order to avoid overvoltages in cast iron parts and damage them.
3.32. At the end of the repair of pumps, other types of equipment, mechanisms before filing the voltage to the electric motor, install the removed safety covers, fencing, covers, etc.
3.33. If malfunctions occur in the operation of the equipment, a dangerous or emergency to stop working, turn off the equipment used and report this to the direct supervisor.
4. Requirements for labor protection in emergency situations
4.1. The following situations may result in an accident or accident:
- performing work with violation of the requirements of this Instruction;
- malfunction of the equipment used in the work, tools, devices;
- operation of equipment that does not comply with the requirements of labor safety;
- careless handling of fire.
4.2. Signing while working with the power tools at least a weak effect of electric current, as well as when the following faults occur immediately, turn it off from the network:
- sudden stop (disappearance of voltage in the network, jamming moving parts, etc.);
- damage to the plug, cable or its protective tube;
- damage to the lid of the brush holder;
- leakage of lubricant from gear or ventilation channel;
- a breakdown or appearance of cracks in the case part, handle, protective - damage to the working part of the tool.
4.3. To stop the pump immediately by clicking the "Stop" button, and turn off the introductory switch in the following cases:
- sudden stopping pump (cessation of electricity supply, electric motor overload, etc.);
- the appearance of smoke or odor characteristic of burning isolation;
- feeling of electrical current when touched by metal parts of the equipment;
- the emergence of increased noise, knock, vibration;
- the emergence of a situation that can lead to an accident or accident.
4.4. With accidents:
- immediately organize the first assistance to the victim and, if necessary, deliver it to a medical organization;
- take urgent measures to prevent the development of emergency or other emergency and the impact of traumatic factors on other persons;
- start before investigating the accident atmosphere, what it was at the time of the incident, if it does not threaten the life and health of other persons and does not lead to a catastrophe, an accident or other emergency circumstances, and in case of the impossibility of maintaining it - to fix the current situation (compile schemes , spend other events).
4.5. In case of fire:
- recovery working in the industrial premises and take measures to extinguish the fire focus. Burning parts of electrical installations and electrical wiring that are under voltage, extinguish a carbon dioxide fire extinguisher;
- take measures to call to the place of fire of the direct supervisor or other officials.
5. Requirements for labor protection at the end of work
5.1. Put in order workplace. Tools, fixtures, details, materials to remove in allotted places.
5.2. At the end of work in the well reliably close it with a lid.
5.3. Remove the means of individual protection, overalls and remove them to the storage location.
5.4. Wash hands with soap, take a warm shower.
5.5. Report directly to the head of all faults seen during work, and measures taken to eliminate them.
The instruction is developed on the basis of "T-130-2002. Typical instruction on labor protection for locksmith-sanitary engineering "(approved. Gosstroke of the Russian Federation 11/21/2002).
On the shoulders of locksmith often the need to fulfill a number of working tasks. Throughout the work time, the mechanic should be protected from a variety of threats - mechanical shocks, excessive humidity, hypothermia and others. When choosing special clothes, its own set itself can differ much and depends on the specific working conditions.
Special clothing set
- A set of special locksmith clothing can consist immediately from several main elements:
- Overalls;
- Boots;
- Jacket.
The composition of the kit may vary, depending on which industry is doing a locksmith. The kit can be complemented by helmet, respirators, protective glasses and other elements. Depending on the scope of work, tissue requirements are also changing. In particular, when working in a car service, an employee must be well insured against sparks, oil and various kinds of combustible substances. For plumbing locks, the main requirement for a set of clothing is to protect against moisture and condensate.
A high-quality set of clothing must certainly be filled with a durable, comfortable fabric. Overalls for locksmiths sews in such a way as to be as comfortable as possible in the sock and not to stance movements.
